Dayman Technical Build Chemicals

Phone : + 90 224 452 55 16

Email : info@dayman.com.tr

MINERAL BASED WATERPROOFING PRODUCTS

CRISTA PLUS – 405

Cement based, added polymer emulsion, contains special chemicals, two component
crystallized waterproofing product

Description

Cement based, added polymer emulsion,
contains special chemicals, two component
crystallized waterproofing product.
Available use for drinking water tank
insulation.
Resistant to hydrostatic pressure.
It fills the empty capillary spaces in concrete
as a result of the reaction with the free
calcium particles by forming crystals.
Available use for the positive and negative
water pressing.

DESCRIPTION:
Cement based, added polymer emulsion,
contains special chemicals, two component
crystallized waterproofing product.
Available use for drinking water tank
insulation.
Resistant to hydrostatic pressure.
It fills the empty capillary spaces in concrete
as a result of the reaction with the free
calcium particles by forming crystals.
Available use for the positive and negative
water pressing.

ADVANTAGES:
Easy and fast application
Extended working time.
Can be applied with brush and spray
equipment
It provides a permanent waterproofing with
the crystals it forms.
It forms a jointless, seamless, permanent,
moisture and waterproof waterproofing
layer.
Resistant to chemicals and salt solutions in
soil.
Available use for moisture surfaces.
Provides high resistance to freeze-thaw
cycle.
Provide the insulation from negative and
positive sides.
Available use for drinking water.
It fills the 0, 4 mm width cracks by forming
the crystals.
It is continuously active.

USAGE AREAS:
Waterproofing of concrete surfaces,
Waterproofing of elevator wells,
Waterproofing of horizontal and vertical
surfaces,
Waterproofing of the negative and positive
parts,
In the water tanks,
In reinforced concretes pipes,
Protect the concrete from the water, salt
and carbon,
Used for waterproofing of structures above
and below in the ground.

( 23 °C Temparature and 50 % for relative
humidity)
Mixture Density : 1950 kg/m3
Application Temperature : +5°C +30°C
Compressive Strenght : 10 bar ( Positive
and negative sides)
Heating Strength : -20°C +80°C between
Coating On : 2 days
Continuous water contact: 7 days later
***These values were obtained as a result
of laboratory tests, just contain finished
applications according to drying time
performance. Due to differences in
temperature and humidity values in the
construction site, the values may change.

Surface Preparation:
The surface; must be cured, dry and
durable. Loose surface mortar and such as
residues should be cleaned and reached
durable surface.
In case of the necessity the surface should
cleaned mechanically
Oil, grease, dirt, paint, salt and vomiting that
prevent adhesion should be removed.
If there are segregation, pits and fractures
on the surface, it should be repaired with
the repair mortar prepared by mixing with
DAYMAN PAIR PLUS and DAYMAN
LATEX C, the mixed mortar should be
applied at least 24 hour before.
Iron and wooden wedges on the surface are
removed and active water leakages and
gaps are formed with DAYMAN D-STOP
SPEED required.
Corners and joints should be chamfered.
The surface should be feed with large
amount of the water, 24 hour before the
application and just before the application it
should moisture again.

Preparation Of The Mixture:
2 kg.liquid component is poured into an
empty and clean bucket and add 5-6 lt.
water.
Pour slowly 25 kg.powder into the water
bucket and use 400 rpm.mixer,
Rest 3-4 minutes to have the mortar.
Before starting the application mix 30
second again.

Application:
The surface to be applied must be wet and
waited until it becomes moist.
Ready product should be applied by roll,
brush and trowel.
It should be applied as 2 -3 time on the
surface.
The application of each layer should be
perpendicular to the previous one.
Wait at least 4 hours and 24 hours until full
drying. Not wait more than 24 hours.
Protective layer such as screed and ceramic
should be applied on the places which has
traffic load.
Ready product must be used in 45 minutes.
The product must be cured by water to not
allow the product desorption,
The expired mortar should be disposed of

Temperature should be between +5 °C and
+35 °C during the application.
Do not apply on surfaces that are at risk of
frost.
In addition, it should not be applied in
extremely hot, rainy or windy weather.
As it has not UV resistance it must be
covered by a cover product when it applies
open areas,
The product should protected from rain,
frost and negative out conditions till it cured,
In cold weather, the reaction will slow down
due to the increase in viscosity and the
application time will be longer,
The product becomes waterproof after 7
days in 23°C,
In 8 day, can be done the water test in
23°C,this time can be vary depending on
the temperature and moist ratio.
While doing ceramic covers, it advised to
use Dayman ceramic adhesive in order to
provide a complete work.

CLEANING OF INSTRUMENTS:
DAYMAN CHRISTA PLUS 2K – 405 should
be cleaned by water when it wet.
DAYMAN CHRISTA PLUS 2K- 405 after
become dry should be cleaned by the
mechanical ways.

CONSUME:
2,00 – 4,00 kg/m².according to water press

PACKING:
Packing: 28 kg. Set
Liquid Component:3,00 kg.
Powder Component: 25,00 kg.
Pallet Dimension: 80×120
Quantity on the Pallet: 60

COLOR:
Grey

SHELF LIFE:
12 months from the production date under
proper storage conditions.
DAYMAN CRISTA PLUS 2K – 405 Liquid
Component should be stored as +5°C’nin in
case of froze under 0 °C temperature.
Used bags must be closed strictly after use.

SAFETY RECOMMENDATIONS:
Wear work clothes, protective gloves,
glasses and masks should be used during
application.
As it cement based do not breathe and do
not touch skin and eyes.
As cured materials has irritating effect, do
not touch with skin and eyes, in case of any
contact rinse with soap and plenty of water,
in case of any swallow see doctor urgently.
Food and beverage materials should not be
kept in the application area and should not
be eaten.
Store out of reach of children.
This product packaging must be disposed of
in accordance with applicable laws.
This responsibility rests with the end user of
the product.
For more information please check the
Material Safety Data Sheet.

LIMITATIONS OF LIABILITY:
The information in this technical data sheet
is given according to technical information,
experience and test result.
As GENERALTÜRK A.Ş. cannot control the
usage of the product that used under which
kind of conditions, it does not accept any
responsibility for the application result and
does not guarantee it.
The product suitability for the product user
should be tested and decided accordingly.
All products should be considered in the
advice of those technical knowledge and
equipment.
GENERAL TURK A.Ş can not accept any
resposibility that occures because of missuse,it only responsible for the written
suggestions that shows the products where
and how use.
GENERALTÜRK A.Ş. It may change the
properties of its products without
announcement.
The technical data sheet is valid until the
next time it is printed and all previous
technical data sheets invalidate the
description

Click to view the Technical Sheet.

× WhatsApp Line