Cement based, polymer modified, has high performance, high strength, resistance to sudden
temperature changes and fine-grained repair mortar.
Description
Cement based, polymer modified, has high
performance, high strength, resistance to
sudden temperature changes and finegrained repair mortar.
DESCRIPTION:
Cement based, polymer modified, has high
performance, high strength, resistance to
sudden temperature changes and finegrained repair mortar.
ADVANTAGES:
Easy and quick to prepare.
High adherence.
Does not shrink
Does not sag on vertical surfaces.
It gives the desired performance in one
layer.
USAGE AREAS:
Repairmen,
Repairmen of the concrete surfaces,
For plastering walls and ceilings,
Can be used in floor preparation before
waterproofing,
( 23 °C Temparature and 50 % for relative
humidity)
Mix Density : 1,70 kg/dm3
Compressive Strength 28 days : ≥ 10
N/mm²
Adherence : 1,00N/mm²
Application Thickness : 2mm-5mm
Total Curing Time : 28 days
Heat Resistance : -20 °C +400°C
Application Temperature : +5°C +35°C
***These values were obtained as a result
of laboratory tests, just contain finished
applications according to drying time
performance. Due to differences in
temperature and humidity values in the
construction site, the values may change.
Surface Preparation:
The surface; must be cured, dry and
durable. Loose surface mortar and such as
residues should be cleaned and reached
durable surface.
If necessary, the surface should be cleaned
mechanically.
Remove oil, grease, dirt, paint, and salt
desorption from adhesion.
The floor should be moistened before
application, but should not be allowed to
water ponding.
Preparation Of The Mixture:
Pour 6-6,50 liters of clean water into an
empty, clean bucket, and slowly replenish
REPAIR PLUS – 905 and mix with a low
speed mixer at 400 rpm until no lumps
remain.
Allow the mortar to rest for 5-10 minutes to
mature.
Mix again for 30 seconds before application.
Using DAYMAN LATEX – C 502 while
preparing the product will increase the
strength of the product and increase the
abrasion resistance.
Application:
The prepared mortar is applied with suitable
equipment.
Min. 5 mm Max 30 mm thickness should be
applied.
Wait until complete drying between layers.
The prepared product should be used within
2-3 hours.
Expired mortar should be disposed of.
The surface temperature during application
should be between +5 °C and+35 °C,
Do not apply on surfaces that are at risk of
frost,
The product must be protected from rain,
water, frost and the other external factors
until curing.
This time may vary according to
temperature and humidity.
CLEANING OF INSTRUMENTS:
DAYMAN REPAIR – 906 – should be
cleaned by water when it wet.
DAYMAN REPAIR 906 – after become dry
should be cleaned by the mechanical ways.
CONSUME:
1, 70 for 1mm meter square
PACKING:
Powder 25, 00 kg. Craft bag
80×120 pallet dimension
54 qty.on pallet
COLOR:
Grey
SHELF LIFE:
1 year from the production date under
proper storage conditions.
Opened packages should be kept tightly
closed.
Wear suitable protective clothing, protective
gloves, goggles and mask during
application.
SAFETY RECOMMENDATIONS:
As it cement based, do not breath and do
not touch with skin and eyes,
Due to the irritating effects of uncured
materials, skin and eyes should not be
contacted, in case of contact with wash
plenty of water and soap, if swallowed seek
medical attention immediately.
Food and beverage materials should not be
kept in the application area and should not
be eaten.
Store out of reach of children.
This product packaging must be disposed of
in accordance with applicable laws.
The responsibility of the disposing is under
end user.
For more information please check the
Material Safety Data Sheet.
LIMITATIONS OF LIABILITY:
The information in this technical data sheet
is given according to technical information,
experience and test result.
As GENERALTÜRK A.Ş. cannot control the
usage of the product that used under which
kind of conditions, it does not accept any
responsibility for the application result and
does not guarantee it.
The product suitability for the product user
should be tested and decided accordingly.
All products should be considered in the
advice of those technical knowledge and
equipment.
GENERAL TURK A.Ş can not accept any
resposibility that occures because of missuse,it only responsible for the written
suggestions that shows the products where
and how use.
GENERALTÜRK A.Ş. It may change the
properties of its products without
announcement.
The technical data sheet is valid until the
next time it is printed and all previous
technical data sheets invalidate the
description
