Dayman Technical Build Chemicals

Phone : + 90 224 452 55 16

Email :



Epoxy based, two components, chemically curing, solvent free orange peel patterned
epoxy topcoat


Epoxy based, two components, chemically
curing, solvent free orange peel patterned
epoxy topcoat.

Epoxy based, two components, chemically
curing, solvent free orange peel patterned
epoxy topcoat.

Orange peel appearance,
High chemical resistance,
Easy to apply.
It has high mechanical strength.
Dries in a short time.
It perfectly covers the surface
It is applied fast.

In and out applications,
Warehouse and facilities,
Mall and shopping centers,
Protection cover in industrial surface
Sewage and waste facilities,
Paper pulp and paper facilities,

( 23 °C Temparature and 50 % for relative
Color : Transparent
Density 20°C: 1,7 gr/cm3
Mixing Ratio : 20 / 3 weight
Flash Point : >90 °C
Application Temperature : +5°C +30°C
Heat Resistance : 121 °C Dry
Compressive Strenght : ~55 N / mm²
Bending Strenght : ~ 25 N / mm2
Absorbing Resistance : Taber :70mg
Hardness Shore D : 80
Adherance (Concrate) : >1,5 N / mm2
Shelf Life : 12 months
Consume : 0,200 – 0,800 Kg /m²
Solid Content : %100
Pot Life : 40 minutes (20°C de)
Dry Time : 6 hours
Coating Again : 8-24 hours
Total Dry :7 days
***These values were obtained as a result
of laboratory tests, just contain finished
applications according to drying time
performance. Due to differences in
temperature and humidity values in the
construction site, the values may change.

Surface Preparation:
The surface; must be cured, dry and
durable. Loose surface mortar and such as
residues should be cleaned and reached
durable surface.
In case of the necessity the surface should
cleaned mechanically
Oil, grease, dirt, paint, salt and vomiting that
prevent adhesion should be removed.

Preparation Of The Mixture:
Must be ensure that the temperature of the
product is between +15°C to +25°C before
the mixing.
Before starting A and B components, the
packages should be 400 rpm until they
reach homogeneous consistency.
It should be mixed with a speed mixer.
Mixed A + B should be mixed by a 400 rpm
low speed mixer for a few minutes until it
reaches a homogenous consistency to
make ready the DAYMAN EPO PAINT 853
for the application.
Remain parts of the mixing bowl and spread
part of the product should be added in to
The mixed product should be transferred to
cleaned bowl when it ready and should remixed.
Pot life of the mixed product is 25°C’de 30
High temperatures will make shorter the pot
life of the mixed product, low temperatures
will make longer.

The surface must be primed with proper
primer before the application.
It should not be over than 24 hours after the
priming process.
It should be spread by trowel in order to
have specified thickness.
The surface is scanned with coral roller
(texture roller) to give the desired texture on
the last layer.
Should be waited minimum 4 days before
Ready product should be applied by roll,
brush and trowel.
Mixed product should be used before the
pot life.
The expired, gelling mixture should not be
used and should be disposed of.

The product is ready in sets and should not
be divided and the eye decision and mixed.
Temperature should be between +5 °C and
+35 °C during the application.
Do not apply on surfaces that are at risk of
In addition, it should not be applied in
extremely hot, rainy or windy weather.
Ensure that the ambient and floor
temperature is between 5 ° C and 30 ° C.
Products should be stored at room
temperature 24 hours before use.
In cold weather, the reaction will slow down
due to the increase in viscosity and the
application time will be longer,
the consumption will increase. Therefore, it
is the most suitable temperature range
between 20 ° C and 25 ° C for easy
application of environment and products.
At high temperatures, the reaction and
application time interval will be accelerated.
After the application, it should be protected
from rain, water, frost and negative external
factors for 24 hours.

DAYMAN EPO PAINT TX – 853 should be
cleaned by solvent when it wet.
become dry should be cleaned by the
mechanical ways.

0,500 – 0,800 kg / m² depending on surface

A + B component: 20, 00 kg
Pallet 80×120
Qty on pallet 18 set 36 bin

Various ral codes.

1 year from the production date under
proper storage conditions.
Should be storage between the temperature
of the DAYMAN EPO PAINT 853 5 °C with
25° C

Do not smoke during the application and
work in a well-ventilated place and away
from naked flames.
Hands and eyes should be protected by
protection equipment.
In case of contact with eyes, rinse
immediately with plenty of water and seek
medical advice.
Food and beverage materials should not be
kept in the application area and should not
be eaten.
It should be known that the solvent is
heavier than air, so remember that it will be
on the ground.
Store out of reach of children.
This product packaging must be disposed of
in accordance with applicable laws.
This responsibility rests with the end user of
the product.
For more information please check the
Material Safety Data Sheet.

The information in this technical data sheet
is given according to technical information,
experience and test result.
As GENERALTÜRK A.Ş. cannot control the
usage of the product that used under which
kind of conditions, it does not accept any
responsibility for the application result and
does not guarantee it.
The product suitability for the product user
should be tested and decided accordingly.
All products should be considered in the
advice of those technical knowledge and
GENERAL TURK A.Ş can not accept any
resposibility that occures because of missuse,it only responsible for the written
suggestions that shows the products where
and how use.
GENERALTÜRK A.Ş. It may change the
properties of its products without
The technical data sheet is valid until the
next time it is printed and all previous
technical data sheets invalidate the

Click to view the Technical Sheet.

× WhatsApp Line