Epoxy Based Low Viscosity Injection Resin
Description
It is a two component, low viscosity and
injection resin which can be used in
reinforcement applications.
DESCRIPTION:
It is a two component, low viscosity and
injection resin which can be used in
reinforcement applications.
ADVANTAGES:
It is a strong binder.
Fast results.
Solvent free.
Easy to apply.
It is resistant to weak acids, microorganisms, alkali and water.
USAGE AREAS:
Foundations.
Veil.
Retaining walls.
Dams.
Waste water plants.
Reinforcement manufacturing of cracked
walls.
( 23 °C Temparature and 50 % for relative
humidity)
A Component :
Color : Transparent – Yellow
Density 20°C : 1,1 gr/cm3
Application Temperature : +5 – +30 °C
Solid Ratio : %100
Total Curing Time :28 days
Shelf Life : 12 months
B Component :
Color : Transparent-Yellow
Density 20°C : 1,1 gr/cm3
Application Temperature :+5 – +30 °C
Shelf Life : 12 months
***These values were obtained as a result
of laboratory tests, just contain finished
applications according to drying time
performance. Due to differences in
temperature and humidity values in the
construction site, the values may change.
Surface Preparation:
The surface; must be cured, dry and
durable. Loose surface mortar and such as
residues should be cleaned and reached
durable surface.
All cracks and joints in the area to be
injected should be cleaned.
All cracks must be sealed by applying one
of the products DAYMAN BOND 860,
DAYMAN BONDEPO 859, DAYMAN BOND
EPO PRO 857.
The packers (injectors) are placed at an
angle of 45 degrees.
The packers should be installed at a
distance of half the thickness of the
reinforced concrete.
The distance between the packers can be
between 15 cm and 90 cm.
The dust which inside of the holes should
be cleaned.
Preparation Of The Mixture:
Before starting A and B components, should
be mixed 400 rpm in its own pack until they
reach homogeneous consistency.
Application:
The prepared packers is applied by injection
pump.
The application pressure can be vary
between 14-200 bars.
The application should be starter from the
first packer.
It starts with low pressure to high pressure
until the resin overflow.
After the resin overflow should be followed
the next packer.
After this application the work is done.
Temperature should be between +5 °C and
+35 °C during the application.
CLEANING OF INSTRUMENTS:
CRACK EPO – 816 should be cleaned by
water when it wet.
CRACK EPO – 816 after become dry
should be cleaned by the mechanical ways.
CONSUME:
For 1 lt.gap approx. 1 kg.
PACKING:
A component 10, 00 kg.
B component 5, 00 kg.
COLOR:
Transparent
SHELF LIFE:
1 year from the production date under
proper storage conditions.
CRACK EPO – 816 should be stored at
temperatures between 5 ° C and 25 ° C.
SAFETY RECOMMENDATIONS:
Wear suitable protective clothing, protective
gloves, goggles and mask during
application.
Do not smoke during application and work
in well-ventilated areas away from naked
flames.
Hands and eyes must be protected with
gloves and protective glasses. In case of
contact with material, wash eyes with plenty
of water rinse and consult a doctor
immediately.
No food or beverage should be allowed in
the application area.
Store out of reach of children.
For more information please check the
Material Safety Data Sheet.
LIMITATIONS OF LIABILITY:
The information in this technical data sheet
is given according to technical information,
experience and test result.
As GENERALTÜRK A.Ş. cannot control the
usage of the product that used under which
kind of conditions, it does not accept any
responsibility for the application result and
does not guarantee it.
The product suitability for the product user
should be tested and decided accordingly.
All products should be considered in the
advice of those technical knowledge and
equipment.
GENERAL TURK A.Ş can not accept any
resposibility that occures because of missuse,it only responsible for the written
suggestions that shows the products where
and how use.
GENERALTÜRK A.Ş. It may change the
properties of its products without
announcement.
The technical data sheet is valid until the
next time it is printed and all previous
technical data sheets invalidate the
description
