Dayman Technical Build Chemicals

Phone : + 90 224 452 55 16

Email : info@dayman.com.tr

SPECIAL PAINTS

THERMAL PAINT– 620

Liquid Heating Insulation Paint For Mineral Surfaces.

Description

It is a water-based, acrylic emulsion based,
high performance, has low heating
conductivity. It is a special coating which
contains ceramic microspheres and
provides thermal insulation on interior and
exterior surfaces.

Category

DESCRIPTION:
It is a water-based, acrylic emulsion based,
high performance, has low heating
conductivity. It is a special coating which
contains ceramic microspheres and
provides thermal insulation on interior and
exterior surfaces.

ADVANTAGES:
It provides 30-35% energy saving for
heating and cooling energy costs depending
on the number of coating application.
When used as wall and ceiling paint, it
reflects the internal radiant heat to inside.
When it is used on the exterior, it reflects to
out the radiant heat that coming from
outside with the sun’s rays.
UV Resistant.
Adherence is very high.
Easy and fast to apply.
Can be applied with brush and spray
equipment.
It has strong penetration.

USAGE AREAS:
Concrete, screed and plaster surfaces.
The surfaces that covered by cement
boarding.
All kind of mineral surfaces.

(23 °C
Temperature and %50 Relative Humidity)
Colour: Various
Consume : 0,250 – 0,500 Kg /m²
***These values were obtained as a result
of laboratory tests, just contain finished
applications according to drying time
performance. Due to differences in
temperature and humidity values in the
construction site, the values may change.

Surface Preparation:
The surface; must be cured, dry and
durable. Loose surface mortar and such as
residues should be cleaned and reached
durable surface.
In case of the necessity the surface should
cleaned mechanically.
Oil, grease, dirt, paint, salt and vomiting that
prevent adhesion should be removed.

Preparation of Mixture:
The product should be mixed with a 400
rpm mixer until it becomes homogeneous.

Application:
It must be primed.
It should be applied to the primed surface
with a roller or brush or spray equipment.
Make sure the surface is dry and then start
applying.
Between the coats must be waited for full
drying.
The tools that used should be cleaned
within 2 hours after application.

Do not apply in the area that has negative
water pressing.
It should be protected from frost, sun and
strong wind first 24 hour after the
application.
The application should be done the area
that contact with the water.
Since the curing of the material will be
slower in cold weather, it should be ensured
that the first coat is completely dry before
applying the 2nd coat.
The ambient and floor temperature should
be between 5 ° C and 30 ° C.

CLEANING OF INSTRUMENTS:
DAYMANTHERMAL PAINT CONCRETTE–
620 should be cleaned by water when it
wet.
DAYMANTHERMAL PAINT CONCRETTE–
620 after become dry should be cleaned by
the mechanical ways.

CONSUME:
0,250 – 0,500 Kg /m²

PACKING:
18, 00 kg

COLOR:
Various

SHELF LIFE:
Shelf Life is 12 months.
Store in a cool and dry area that protected
from frost, away from direct sunlight.
Do not stack the pallets top of each other
and use the first in first out progress.

SAFETY RECOMMENDATIONS:
Wear suitable protective clothing, protective
gloves, goggles and mask during
application.
Do not smoke during application and work
in well-ventilated areas away from naked
flames.
Hands and eyes must be protected with
gloves and protective glasses, in case of
contact with material, wash eyes with plenty
of water rinse and consult a doctor
immediately.
It should be noted that solvents are heavier
than air and therefore circulate on the
ground.
No food or beverage should be allowed in
the application area.
Store out of reach of children.
For more information please check the
Material Safety Data Sheet.

LIMITATIONS OF LIABILITY:
The information in this technical data sheet
is given according to technical information,
experience and test result.
As GENERALTÜRK A.Ş. cannot control the
usage of the product that used under which
kind of conditions, it does not accept any
responsibility for the application result and
does not guarantee it.
The product suitability for the product user
should be tested and decided accordingly.
All products should be considered in the
advice of those technical knowledge and
equipment.
GENERAL TURK A.Ş cannot accept any
responsibility that occurs because of missuse, it only responsible for the written
suggestions that shows the products where
and how use.
GENERALTÜRK A.Ş. It may change the
properties of its products without
announcement.
The technical data sheet is valid until the
next time it is printed and all previous
technical data sheets invalidate the
description

Click to view the Technical Sheet.

× WhatsApp Line