TEX BAND 2910
Triplex, transverse high-flex that covered with special polypropylene (PP) by two side, felt
coated chamfer band.
Description
Triplex, transverse high-flex that covered
with special polypropylene (PP) by two side,
felt coated chamfer band.
- Usage Areas
- Technical Specifications
- Method of Application
- Additional Information
- Technical Leaflet
- Videos
DESCRIPTION:
Triplex, transverse high-flex that covered
with special polypropylene (PP) by two side,
felt coated chamfer band.
ADVANTAGES:
It is economical.
Faster.
Easy to apply.
Can crack bridges.
It is alkali resistant.
Resistant to chemicals.
USAGE AREAS:
Can be used with all sliding waterproofing
products.
( 23 °C Temparature and 50 % for relative
humidity)
Product Carrier : Polyester felt
Roll Length : 50 mt
***These values were obtained as a result
of laboratory tests, just contain finished
applications according to drying time
performance. Due to differences in
temperature and humidity values in the
construction site, the values may change.
Surface Preparation:
The surface; must be cured, dry and
durable. Loose surface mortar and such as
residues should be cleaned and reached
durable surface.
Deep gaps on the surfaces should be
repaired by DAYMAN REPAIR PLUS,
DAYMAN EPO MORTAR or DAYMAN
BOND EPO.
Application:
The product is applied to surface that has
been prepared before and the suitable
sliding waterproof product is applied.
After the product application DAYMAN TEX
BAND 2910 is bonded.
When the product is adhered to the surface,
should be attended to not have any air
bubbles under it.
Joints should be adhered by making 5-10
cm overlap.
Should be done the second layer on the
surface.
If the weather is rainy or possible rainy days
the application should not be done,
After the application it must be protected
from strong wind, storm and sun in the first
24 hours,
The application should be made on the part
of the structure that comes into contact with
water.
As the product become slowly cured in the
cold weathers, the second coating must be
done when the first coating is completely
becoming dry.
Ensure that the ambient and floor
temperature is between +5 ° C and +30 ° C.
CLEANING OF INSTRUMENTS:
Should be cleaned by solvent when it wet.
After become dry should be cleaned by the
mechanical ways.
CONSUME:
§ 1,00 mt/mt.
PACKING:
50, 00 mt roll.
12 cm width. / can be produced for special
dimensions)
SHELF LIFE:
24 months.
SAFETY RECOMMENDATIONS:
Wear suitable protective clothing, protective
gloves, goggles and mask during
application.
Do not smoke during application and work
in well-ventilated areas away from naked
flames.
Hands and eyes must be protected with
gloves and protective glasses. In case of
contact with material, wash eyes with plenty
of water rinse and consult a doctor
immediately.
No food or beverage should be allowed in
the application area.
Store out of reach of children.
For more information please check the
Material Safety Data Sheet.
LIMITATIONS OF LIABILITY:
The information in this technical data sheet
is given according to technical information,
experience and test result.
As GENERALTÜRK A.Ş. cannot control the
usage of the product that used under which
kind of conditions, it does not accept any
responsibility for the application result and
does not guarantee it.
The product suitability for the product user
should be tested and decided accordingly.
All products should be considered in the
advice of those technical knowledge and
equipment.
GENERAL TURK A.Ş cannot accept any
responsibility that occurs because of missuse, it only responsible for the written
suggestions that shows the products where
and how use.
GENERALTÜRK A.Ş. It may change the
properties of its products without
announcement.
The technical data sheet is valid until the
next time it is printed and all previous
technical data sheets invalidate the
description