CERA-CEM FLEX – 910
High Performance, Elastic,Has Stability by Reduce Sliding, Ceramic, Porcelain and
Granite Adhesive
Description
High Performance, Elastic,Has Stability by
Reduce Sliding, Ceramic, Porcelain and
Granite Adhesive Mortar with Long Working
Time.
- Usage Areas
- Technical Specifications
- Method of Application
- Additional Information
- Technical Leaflet
- Videos
DESCRIPTION:
High Performance, Elastic,Has Stability by
Reduce Sliding, Ceramic, Porcelain and
Granite Adhesive Mortar with Long Working
Time.
ADVANTAGES:
Easy and fast preparation.
High elastic performance.
Extended working time.
High adherence.
Available use from up to down.
Saves from labors.
USAGE AREAS:
Available use for ceramic, tile, glass mosaic,
marble, granite and etc.
Indoor Applications:
For vertical and horizontal surfaces.
Bath, WC, kitchen, wet areas.
Wall and floor.
Balcony and terrace.
Large areas.
Outdoor Applications:
Floor
Wall
( 23 °C Temparature and 50 % for relative
humidity)
Aderance : ≥ 1,0 N/mm²
Start : ≥ 1,0 N/mm²
After Water Immersing : ≥ 1,0 N/mm²
After Age Heating : ≥ 1,0 N/mm²
After Freezing-Thawing Cycle : ≥ 1,0
N/mm²
Heating Resistance : (-40°C) – (+80°C)
Pot Life : 1 Hour
Working Time : 30 Minutes
Gouting the Floor : 12 Hours
Timing for Vertical Grouting : 18 Hours
***These values were obtained as a result
of laboratory tests, just contain finished
applications according to drying time
performance. Due to differences in
temperature and humidity values in the
construction site, the values may change.
Surface Preparation:
The surface; must be cured, dry and
durable. Loose surface mortar and such as
residues should be cleaned and reached
durable surface.
In case of the necessity the surface should
cleaned mechanically
Oil, grease, dirt, paint, salt and vomiting that
prevent adhesion should be removed.
If there are segregation, pits and fractures
on the surface, it should be repaired with
the repair mortar prepared by mixing with
DAYMAN PAIR PLUS and DAYMAN
LATEX C, the mixed mortar should be
applied at least 24 hour before.
The floor should be moisted before the
application.
Before the ceramic cover application, it
should definitely prime by DAYMAN ST
PRIMER.
Preparation Of The Mixture:
6,25 -6,75 liter water is poured into an
empty and clean bucket.
Pour slowly 25 kg. powder into the water
bucket and use 400 rpm. mixer until
eliminate chunks of the powders.
Rest 5 minutes to have the mortar.
Before starting the application mix 30
second again.
Application:
Proper working time is 2 hour for CERACEM FLEX – 910, suitable area should be
specified and the surface should be covered
by toothed trowel in this time.
The tiles should be placed on the adhesive
as leaving a joint gap.
In order to get the best result from the
application, the tiles should be placed well
with the rubber hammer and the air should
be out in the tiles
Temperature should be between +5 °C and
+35 °C during the application.
Do not apply on surfaces that are at risk of
frost.
In addition, it should not be applied in
extremely hot, rainy or windy weather.
These conditions can make shorter the
working time.
After finishing of the working time, touch the
surface by finger.
If occurred a film, remove the adhesive from
the surface and apply it again.
The expired or crusted mortar in the bucket
should not be used and should be disposed
of.
Wash the hands and used instruments with
plenty of the water after the application.
The surface that remained adhesive should
be cleaned by wet rag.
It should prevent from direct water contact
and pedestrian traffic in 24 hours.
CLEANING OF INSTRUMENTS:
DAYMAN CERA CEM FLEX–910 should be
cleaned by water when it wet.
DAYMAN CERA CEM FLEX-910 after
become dry should be cleaned by the
mechanical ways.
CONSUME:
3, 50 – 5, 00 kg/m²- various.
PACKING:
25, 00 kg in a craft bag
80×120 pallet dimesion
54 Pcs. on the Pallet
COLOR:
Grey- White
SHELF LIFE:
1 year from the production date under
proper storage conditions.
SAFETY RECOMMENDATIONS:
Wear work clothes, protective gloves,
glasses and masks should be used during
application.
As it cement based, do not breath and do
not touch with skin and eyes,
Due to the irritating effects of the cured
materials, skin and eyes should not be
contacted, in case of contact with wash
plenty of water and soap, if swallowed seek
medical attention immediately.
Food and beverage materials should not be
kept in the application area and should not
be eaten.
Store out of reach of children.
This product packaging must be disposed of
in accordance with applicable laws.
This responsibility is belong the end user.
For more information please check the
Material Safety Data Sheet.
LIMITATIONS OF LIABILITY:
The information in this technical data sheet
is given according to technical information,
experience and test result.
As GENERALTÜRK A.Ş. cannot control the
usage of the product that used under which
kind of conditions, it does not accept any
responsibility for the application result and
does not guarantee it.
The product suitability for the product user
should be tested and decided accordingly.
All products should be considered in the
advice of those technical knowledge and
equipment.
GENERAL TURK A.Ş can not accept any
resposibility that occures because of missuse,it only responsible for the written
suggestions that shows the products where
and how use.
GENERALTÜRK A.Ş. It may change the
properties of its products without
announcement.
The technical data sheet is valid until the
next time it is printed and all previous
technical data sheets invalidate the
description