DK 100
Polyester felt used as sliding waterproofing products as chamfering tape in corner turns.
Description
Polyester felt used as sliding waterproofing
products as chamfering tape in corner turns.
- Usage Areas
- Technical Specifications
- Method of Application
- Additional Information
- Technical Leaflet
- Videos
DESCRIPTION:
Polyester felt used as sliding waterproofing
products as chamfering tape in corner turns.
ADVANTAGES:
Economical.
Faster.
Easy application.
Crack bridging.
Alkali resistant.
Resistant to chemicals.
USAGE AREAS:
DAYMAN BITUMEN PLUS 300
DAYMAN BITUMEN 302
DAYMAN BITUMEN 303
DAYMAN AQUAFLEX 200
DAYMAN AQUAFLEX UV 202
DAYMAN AQUAPOL 810
DAYMAN AQUAPOL UV 811
DAYMAN BITUMEPOL 812
DAYMAN AQUAPOL 2K 813
DAYMAN AQUA HIBRIT 1001
DAYMAN AQUA HIBRIT TRANS 1002
Can be used with the application of the
product that specified above.
(23 °C Temperature and %50 Relative Humidity)
Product Carrier : Polyester Felt
Roll Length: 100mt.& 400 mt
Width : 1,00mt & 1,5 mt
Thickness : apprx. 0,5mm
***These values were obtained as a result
of laboratory tests, just contain finished
applications according to drying time
performance. Due to differences in
temperature and humidity values in the
construction site, the values may change.
Surface Preparation:
The surface; must be cured, dry and
durable. Loose surface mortar and such as
residues should be cleaned and reached
durablesurface.
Deep gaps on the surfaces should be
repairedbyDAYMANREPAIRPLUS,
DAYMAN EPO MORTAR or DAYMAN
BOND EPO.
Application:
The product is applied to surface that has
been prepared before.
After the product application DAYMAN DK
100 is bonded.
When the product is adhered to the surface,
should be attended to not have any air
bubbles under it Joints should be adhered by making 5-10
cm overlap.
Should be done the second and third layer
on the surface.
If the weather is rainy or possible rainy days
the application should not be done,
After the application it must be protected
from strong wind, storm and sun in the first
24 hours,
The application should be made on the part
of the structure that comes into contact with
water.
As the product become slowly cured in the
cold weathers, the second coating must be
done when the first coating is completely
becoming dry.
Ensure that the ambient and floor
temperature is between 5 ° C and 30 ° C.
CLEANING OFINSTRUMENTS:
Should be cleaned by solvent when it wet.
After become dry should be cleaned by the
mechanical ways.
CONSUME:
1,10m2/ m2
PACKING:
1,00 x 100 mt=100 m2/Roll
1,50 x 400 mt=600 m2/Roll
SHELF LIFE:
24 months.
SAFETY RECOMMENDATIONS:
Wear suitable protective clothing, protective
gloves, goggles and mask during
application.
Do not smoke during application and work
in well-ventilated areas away from naked
flames.
Hands and eyes must be protected with
gloves and protective glasses. In case of
contact with material, wash eyes with plenty
of water rinse and consult a doctor
immediately.
No food or beverage should be allowed in
the application area.
Store out of reach of children.
For more information please check the
Material Safety Data Sheet.
LIMITATIONS OF LIABILITY:
The information in this technical data sheet
is given according to technical information,
experience and test result.
AsGENERALTÜRKA.Ş. cannot controlthe
usage of the product that used under which
kind of conditions, it does not accept any
responsibility for the application resultand
does not guarantee it.
The product suitability for the product user
should be tested and decided accordingly.
All products should be considered in the
advice of those technical knowledge and
equipment.
GENERAL TURK A.Ş cannot accept any
responsibility that occurs because of missuse, it only responsible for the written
suggestions that shows the products where
and how use.
GENERALTÜRK A.Ş. It may change the
properties of its products without
announcement.
The technical data sheet is valid until the
next time it is printed and all previous
technical data sheets invalidate the
description