D-THERM – 552
Cement based, polymer reinforced,fiber, containing special chemical additives, one
component
Description
Cement based, polymer reinforced,fiber,
containing special chemical additives, one
component, used in the mineral surfaces as
a thermal insulation plaster board.
- Usage Areas
- Technical Specifications
- Method of Application
- Additional Information
- Technical Leaflet
- Videos
DESCRIPTION:
Cement based, polymer reinforced,fiber,
containing special chemical additives, one
component, used in the mineral surfaces as
a thermal insulation plaster board.
ADVANTAGES:
Excellent adhesion to mineral surfaces.
Easy to apply.
Water vapor permeable.
Resistant to freeze – thaw cycle.
Easy to prepare.
Working time is long.
USAGE AREAS:
Indoor and outdoor areas.
As an adhesive in jacketing manufacturing.
It is used as surface repair mortar on all
mineral surfaces.
Used as repair plaster before the painting.
((23°C, %50 Relative Humudity)
Dry Bulk Density :1350 ± 200 kg/m3
Compressive Strength 28 days: CSIV
Total Curing Time : 28 Days
Temperature Strength :-20 °C +80°C
Application Temperature :+5°C +30°C
Color : Grey
***These values were obtained as a result
of laboratory tests, just contain finished
applications according to drying time
performance. Due to differences in
temperature and humidity values in the
construction site, the values may change.
Preparation Of The Mixture:
6- 6, 5 liter water is poured into an empty
and clean bucket, pour slowly D-THERM
551 into the water bucket and use 400 rpm
mixer until eliminate chunks of the powders.
Rest 5 minutes to have the mortar.
Before starting the application mix 30
second again.
Application:
DAYMAN D-THERM 552 is applied
homogeneously with a steel trowel as 3
mm. thickness on the surface of the
insulation board that is applied DAYMAN DTHERM 551 adhesive mortar and
mechanically fixed the surface with the
available dowel.
The mesh is laid on the plaster and pressed
to the middle of the mortar.
If necessary, thickness can be increased
(max. 5 mm).
The prepared mixture should be used within
1 hour.
Temperature should be between +5 °C and
+35 °C during the application.
Do not apply on surfaces that are at risk of
frost.
In addition, it should not be applied in
extremely hot, rainy or windy weather.
The product should be protected from rain,
water, frost and negative external factors
until curing.
CLEANING OF INSTRUMENTS:
DAYMAN D-THERM 552 should be cleaned
by water when it wet.
DAYMAN D-THERM 552 after become dry
should be cleaned by the mechanical ways.
CONSUME:
Various 4, 00-6, 00 kg/m².
PACKING:
25, 00 in a craft bag
110×100 pallet dimesion
64 qty on Pallet
COLOR:
Grey
SHELF LIFE:
1 year from the production date under
proper storage conditions.
Close tight the opened bags.
LIMITATIONS OF LIABILITY:
The information in this technical data sheet
is given according to technical information,
experience and test result.
As GENERALTÜRK A.Ş. cannot control the
usage of the product that used under which
kind of conditions, it does not accept any
responsibility for the application result and
does not guarantee it.
The product suitability for the product user
should be tested and decided accordingly.
All products should be considered in the
advice of those technical knowledge and
equipment.
GENERAL TURK A.Ş can not accept any
resposibility that occures because of missuse,it only responsible for the written
suggestions that shows the products where
and how use.
GENERALTÜRK A.Ş. It may change the
properties of its products without
announcement.
The technical data sheet is valid until the
next time it is printed and all previous
technical data sheets invalidate the
description